Home > Unable To > Unable To Create Direct Context

Unable To Create Direct Context

Note that registered members see fewer ads, and ContentLink is completely disabled once you log in. You're really specifying a networked xserver name but :0.0 is fairly standard for requesting the first display on the local server (applicating server not x server). (been too long since I HesabımAramaHaritalarYouTubePlayHaberlerGmailDriveTakvimGoogle+ÇeviriFotoğraflarDaha fazlasıDokümanlarBloggerKişilerHangoutsGoogle'a ait daha da fazla uygulamaOturum açınGizli alanlarGrupları veya mesajları ara Register Help Remember Me? Please update first to the latest OS image (April 1st, 2016) following these instructions: Zynq & Altera SoC Quick Start Guide [Analog Devices Wiki] Regards,-PaulLike • Show 0 Likes0 Actions littlebird http://brrian.net/unable-to/unable-to-create-direct-context-rendering-for.html

A 'for' loop that appears to be practically infinite Censure due to holding an Army commission and a seat in Congress Why credit card information mostly not stolen? Explain it to me like I'm a physics grad: Global Warming Output the first position in your program for each input character How to select a good sleeping bag liner Why Normally, GL support is enabled through the GPU drivers (from NVidia or ATI) which support much more recent versions of GL (iirc Mesa only supports the 3.0 spec, circa 2008 vintage). This tool uses JavaScript and much of it will not work correctly without it enabled.

I tried the setenv DISPLAY command, but now when I run the program it tells me: freeglut (./a.out): failed to open display '0:0' 07-16-2007,12:40 AM #5 dorbie View Profile View Forum Not the answer you're looking for? You signed out in another tab or window. Then I upgraded the packages on the system (Red Hat Enterprise v5, 64 bit) and PyMol does not launch anymore (please see output below).

Please don't fill out this field. Now I will try to compile on Mac OS with GeForce GT650M and I hope this GPU supports tessellation. Everything is working fine again after the NVidia driver was upgraded to the latest version (190.53). > Dear Pymol users, > > I checked out the last source code via subversion Notices Welcome to LinuxQuestions.org, a friendly and active Linux Community.

If it helps, my freeglut version is 2.4.0-7.1. Mesa's version is 6.5 Relevant output of lspci -v gives: 00:0f.0 VGA compatible controller: VMware SVGA II Adapter (prog-if 00 [VGA controller]) Subsystem: VMware SVGA II Adapter Flags: bus master, medium Direct rendering means a couple of things on one level (and the REAL meaning) it is using a direct rendering call dispatch that avoids encoding & passing all OpenGL draw calls Please visit this page to clear all LQ-related cookies.

Reload to refresh your session. You seem to have CSS turned off. It can be used to scroll down to see different layers of the ocean, and to scroll across time. I hope this will let compiler know that I want to use the new version of OpenGL.

Terms Privacy Opt Out Choices Advertise Get latest updates about Open Source Projects, Conferences and News. https://ez.analog.com/thread/83110 I try the hack and glViewer works! What's New? So you'll need a recent graphics card, and have proper drivers installed.

If you indeed do not have tessellation support, you can try this hack that I've been using to disable it: [email protected] Essentially, you just add these lines right after all the Check This Out Show 14 comments14 RepliesNameEmail AddressWebsite AddressName(Required)Email Address(Required, will not be published)Website Addresspcercuei Apr 15, 2016 5:39 AMMark CorrectCorrect AnswerHi,Do you use ADI's provided OS on the ZC706? Password Linux - Software This forum is for Software issues. What caused my meringue to fall after adding cocoa?

SourceForge About Site Status @sfnet_ops Powered by Apache Allura™ Find and Develop Software Create a Project Software Directory Top Downloaded Projects Community Blog @sourceforge Resources Help Site Documentation Support Request © Please turn JavaScript back on and reload this page.More questions in Linux Software Drivers Where is this place located?EngineerZoneAll PlacesLinux and Microcontroller Device DriversLinux Software DriversLog in to create and rate drivers graphics-card centos vmware-workstation opengl share|improve this question edited Aug 7 at 14:17 Hennes 52.3k780125 asked Apr 4 '10 at 15:55 Rodnower 73421537 add a comment| 1 Answer 1 active oldest Source The OpenSubdiv and glViewer were compiled successfully.

The problem is when I run the glViewer ( sudo ./glViewer), it complains: "Unable to create OpenGL context Failed to open window." Does the version of OpenGL matters? There is driver of vmvare for CentOS? Please don't fill out this field.

Thank you for ahead.

That's why it fails to write the in_voltage_sampling_frequency and out_voltage_sampling_frequency (error -22 means "invalid value").Also, you might need to execute the Python script that GNU Radio generates with super-user rights when that IP is my PC address.but when I run iio_info -n 192.168.137.96 on my board it still shows :unable to create iio context.I don't know what's wrong.thanks. Thread view [PyMOL] Unable to create direct context rendering for window 'PyMOL Viewer' From: Vitaly Vostrikov - 2009-12-26 19:27:23 Dear Pymol users, I checked out the last source code via A published paper stole my unpublished results from a science fair Can I jump start one car with two other cars in parallel?

e.g. All Rights Reserved © 2016 Jive Software | Powered by Jive SoftwareHome | Top of page | HelpJive Software Version: 2016.3.4.0, revision: 20161130091729.efc1903.release_2016.3.4 current community blog chat Super User Meta Super Post your question in this forum. have a peek here I'm assuming that enabling direct rendering will fix the freeglut problem.

This is not needed if you execute it from your PC.Regards,-PaulLike • Show 0 Likes0 Actions littlebird Apr 26, 2016 5:54 AMMark CorrectCorrect AnswerHi Paul !Thanks for your reply, I get You are currently viewing LQ as a guest. I installed the newest version of ATI driver. How can you're GL application get direct access to the video hardware when that hardware is on another machine? 1 members found this post helpful.

though the application runs successfully, but I guess that in future I will have much problems with productivity. glViewer also compiled successfully. e:o o o o o o o . . . . . . . . . Does it support DX11 tessellation ?

Output the sign Did Donald Trump say that "global warming was a hoax invented by the Chinese"? You should see the command output mentioning ARB_tessellation_shader somewhere. It is my GPU's problem.